Инструкция по запуску

1.

unpacking tools
Page 1
Confidential / Copyright ©2016 Profeta All Right Reserved.

2.

Battery (customer preparation)
Page 2
LR44
AAA
BR2032
Two for the gague
four for the mouse and keyboar
One for the PC
Confidential / Copyright ©2016 Profeta All Right Reserved.

3.

Dismantle the wooden box
use unpacking tools to remove
wooden board
use knife to cut packing films
use unpacking tools to remove
4 fixed feet and 2 pieces of
wood
Page 3
Confidential / Copyright ©2016 Profeta All Right Reserved.

4.

Carton
Open the cardboard box
Page 4
Power cord
Mouse and keyboard
Dust board
Confidential / Copyright ©2016 Profeta All Right Reserved.

5.

Material box
Wooden case
Page 5
Wooden box materials
Confidential / Copyright ©2016 Profeta All Right Reserved.

6.

Fixed equipment
Release the anchor device by hand
Page 6
Use a forklift to move the equipment
Fixed equipment
to the ground
Confidential / Copyright ©2016 Profeta All Right Reserved.

7.

Battery installation
Install the batteries for the mouse
and keyboard
Page 7
Install the mouse and keyboard receivers
Install the battery of the measuring device
Confidential / Copyright ©2016 Profeta All Right Reserved.

8.

Battery installation
Host
Page 8
Battery installation
Pay attention to the positive
and negative poles
Confidential / Copyright ©2016 Profeta All Right Reserved.

9.

key and light
Key installation
Page 9
Installation of indicator lights
Confidential / Copyright ©2016 Profeta All Right Reserved.

10.

Connect the power cord
N
Connection interface
Page 10
Another section for
connecting the power
supply
PE
L
brown cable power
blue cable 0
yellow/green cable earth cable
Confidential / Copyright ©2016 Profeta All Right Reserved.

11.

Printing preparation and take out
plate
Nanjing Profeta Intelligent Technology Co., Ltd
Web: www.profeta3d.com
Add:
Nanjing,
211111,
Confidential
/ Copyright ©2014
profeta AllChina
Right Reserved.

12.

Printing preparation check list Power
on
The horizontal state is turn off,
and the vertical state is turn on
Page 12
Turn on the main switch on the
Turn the power-on key switch
back of the machine
and press the power on button
Confidential / Copyright ©2016 Profeta All Right Reserved.

13.

login software
Login account and password
are same: User
Page 13
Select power “On” and
lighting”On”on the Manual
Confidential / Copyright ©2016 Profeta All Right Reserved.

14.

Copy the folder where the files
output by P3DS to the printer
desktop via a USB flash drive: The
picture shows a USB interface
Page 14
Importing data:Click "Open" to select the folder to be imported via the USB drive
Confidential / Copyright ©2016 Profeta All Right Reserved.

15.

the system will prompt out the minimum required powder height: Record the height
Page 15
Confidential / Copyright ©2016 Profeta All Right Reserved.

16.

In the PowerControl area
In the LightingSwitch area
click On. Then, the button is
click ON. A yellow bulb
grayed out, and you can
appears on the right side, and
operate the machine now.
the lighting inside the chamber
is turned on.
Page 16
In the Build Piston area click
PositionSet without modifying the
value 0 in the front. The top of the
build piston will automatically reach
the zero position, which is level with
the reference platform
Confidential / Copyright ©2016 Profeta All Right Reserved.

17.

Clean the chamber: Clean the
powder residue of the last printing
task from the reference platform
and build piston, ensure that there
is no obvious powder residue.
Page 17
Prepare the plate: Ensure that the
surface of the plate is flat and
smooth. If there is any dirt, clean it
with anhydrous ethanol.
Put the plate onto the build
piston(plate and build piston
are fixed by magnetic force
Confidential / Copyright ©2016 Profeta All Right Reserved.

18.

The height gauge needs to be zeroed before measurement:
- Press the OFF/ON button on each of the two dial gauges to turn on.
- Place the height gauge on the reference platform, ensuring that the two feet of the base are on the
reference platform, and then press the ZERO button on the right. When the value is 0 on both dial
gauges, it indicates that the calibration is complete.
Page 18
Confidential / Copyright ©2016 Profeta All Right Reserved.

19.

The plate height we need is 1 mm:
Measure the printing plate 3 times in the middle, left, and right
Flatness standard: The error range of the height value of the measuring point is 1 ± 0.05mm 0.95~1.05
Page 19
Confidential / Copyright ©2016 Profeta All Right Reserved.

20.

Coating ratio setting:
For full
crown&copings, it is
generally
recommended to set
the coating ratio to
260%.
For removable partial
dentures, it is
generally
recommended to set
the coating ratio to
180%
Page 20
Confidential / Copyright ©2016 Profeta All Right Reserved.

21.

the height of the powder should be
10mm higher than the minimum
requirement of the system:check
the" Pos" of the "Powder Piston",it's
the height of the powder
Compact the powder:use a shovel to
compact the powder. Insert the front
Powder laying: Raise the powder piston so that the powder is 2mm above the
reference plateform. Then control the coater to move 300mm to the right. If
there are depressions or unevenness on the powder-laying surface, return the
end of the shovel into the powder and
shake it back and forth, left and right,
scraper to zero. Continue to lift the powder piston and control the coater to
and repeat the operation multiple
the height of the powder is greater than the minimum required height
times.
Qualification criteria: The surface of the powder piston is flat/there is only a thin
move 300mm to the right.
repeat this several times until the powder-laying surface is completely flat and
layer of powder on the plate/there are no obvious traces on the powder path
Page 21
Confidential / Copyright ©2016 Profeta All Right Reserved.

22.

Clean the chamber door seal
rubber: use the normal tissue
with anhydrous ethanol to
clean it
Page 22
Clean the protect glass:use specialized
lens paper with anhydrous ethanol to
wipe it in a circular motion and then use
new dry lens paper to wipe the protective
glasses in the same circular motion
Put in the dust barrier and
close the chamber door
Confidential / Copyright ©2016 Profeta All Right Reserved.

23.

click the "Start"
Page 23
Confidential / Copyright ©2016 Profeta All Right Reserved.

24.

After printing is completed, the
Cleaning the dust barrier
take out the dust barrier
system will prompt "Building
completed",click“OK” then open
the door
Page 24
Confidential / Copyright ©2016 Profeta All Right Reserved.

25.

click the “On” of the
PowerControl
Page 25
Confidential / Copyright ©2016 Profeta All Right Reserved.

26.

set "Position" to "0", and then click
"Positionset", the build piston will
automatically rise to the 0 position,
clean the powder on the plate in the
same time
Page 26
use a rubber hammer or an
use the compressed air of the air
Allen tool to tap the back of the
gun to blow out the remaining
plate, and pour out the
powder.
remaining powder.
Confidential / Copyright ©2016 Profeta All Right Reserved.

27.

Hardware introduction _Nitrogen generator
Nitrogen generator BDL-A10 220V
B
C
A
A
B
D
open the cove and take out two tubes
A-A C-C
B-B D-D
Page 27
Confidential / Copyright ©2016 Profeta All Right Reserved.

28.

Hardware introduction _Nitrogen generator
Nitrogen generator BDL-A10 220V
nitrogen purity
D
running button
B
air compressor
pressure
≥0.6mpa
tube from nitrogen generator
Page 28
compressor connection be made
by customer
compressor air need dry and
without water oil
remark this nitrogen
generator will fill gas
to printer at beginning
no need to wait
achieve high purity
Confidential / Copyright ©2016 Profeta All Right Reserved.

29.

Hardware introduction _Vaccum Furance
Atmosphere Furance
Page 29
Confidential / Copyright ©2016 Profeta All Right Reserved.

30.

Hardware introduction _Cutting
Cutting (DLY-115W1)
Page 30
Confidential / Copyright ©2016 Profeta All Right Reserved.

31.

Hardware introduction _Sieving machine
sieving machine
Page 31
Confidential / Copyright ©2016 Profeta All Right Reserved.

32.

联系我们
南京前知智能科技有限公司
Web www.profeta3d.com
Email service@profeta3d.com
Add 中国江苏省南京市江宁区秣周东路12号
Page 32
Confidential / Copyright ©2016 Profeta All Right Reserved.